Nightforce one-piece bases are machined to exact Mil-Std. 1913 specification rail dimensions, assuring perfect alignment. This design allows the same scope to be used on several different rifles, always optimizing eye relief. Choose from 20MOA or 40MOA tapers (40MOA for Remington actions only). Designed and machined for right- or left- handed actions, Nightforce bases will never interfere with loading or extraction. A168 - Fits Round Receivers
SPECS: Win SA base does not fit WSM Models.
Další...
Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
SPECS: Základna Win SA není kompatibilní s modely WSM.
Další...
Hodnocení zákazníků pro položku NIGHTFORCE REMINGTON 700 SHORT ACTION 40 MOA BASE
Počet hodnocení: 8
Od brownells.com: 8
Průměrné hodnocení: 4,5
Does not fit Savage 10 Ashbury Precision(21.11.2017)
First off, the rail is terrific. Steel, perfect level, four screws included (torx head). BUT - be careful if you have a Savage 10 Ashbury Precision. This rail extends an inch or so forward of the front screws and is not high enough to clear the Ashbury handguard. Just wanted to warn any Ashbury owners.
Fit like a glove(20.5.2013)
Expensive and worth every penny.
Broken recoil lug(1.4.2014)
Initially I thought it to be of high quality with a good fit. I tightened the mounting screws well with blue Locktite (did not use torque wrench) and all seemed well however after about 200 rounds 300 Win Mag I noticed erratic groups much worse than initially. I then noticed the recoil lug was cracked and then it fell off when I removed it. I noticed only the second from the front mounting screw to be slightly loose. Luckily they were intact (not sheared off) except for the front screw slightly bent backward (unscrewing noted some rubbing on one side of the screw hole. My load development did go up to loads that had high pressure signs but I stopped immediately after that. The majority of shots were around 78 grains of AA Magpro powder with only flattened primers (ok extraction, no severe cratering). I also used a Lead Sled with about 50lbs of lead so that should have reduced the recoil impulse on the recoil lug. I think the rail should not have failed. The recoil lug is very thin maybe 2mm max. Maybe ok in 308 but not strong enough for the belted Magnums. I was able to zero my Nightforce Competition Scope at 100yds with the 40MOA about 3-4 MOA of down elevation left. So okay at short range if don't need to change windage much
Great value(16.11.2010)
Purchased this from Brownells a while back. I needed more elevation for my Leupold mk4 MR. I am very pleased with this product. It is built quite heavy and works great with the Leupold MK4 rings. As I build more rifles I will use these bases again.
A+ if rifle tapped for right screw(6.3.2010)
This base is designed to never move once mounted. Just make sure your rifle isn't tapped for 8X40 screws like a lot of magnums are. The reason I say this is because you'll be redrilling the mount out and finding larger screws to fit like I am. If Nightforce would tell you the screw size, I never would have ordered this mount for my 300RUM custom made rifle.
Screws(5.1.2012)
Previous review is correct, People often buy NightForce to mount on heavy recoiling long range rifles. (like my Remington in .338 Lapua) These rifles will often have 8 X 40 mount screws but this base is machined for a lighter screw. You will have to re-drill/machine this base to use it on a heavy recoiling rifle with 8 X 40 mounting holes
Best base on the market(25.7.2012)
Anyone that complains that these bases have to be modified to fit a Remington 700 in a magnum has not done their research. Nightforce does offer a 700 base with 8-40 screws. It is called the HS/700 base. A simple call to NF or reading passed the header in the listing would make it clear. I use these bases exclusively on my 6-48 Remington 700 rifles. They have never failed me whether or not I have bedded them. They are bullet proof and absolutely machined to the tightest tolerances. Many of my rifles that I have checked base screw hole alignment have required next to zero windage adjustment with Nightforce scopes, rings, and bases. Thank you Brownells for carrying such high quality components for us.
Simply the best(25.2.2014)
Chose this base for a custom build (Remington 700 short action in .308, Shilen short-chambered Remington stainless barrel, heavy #7 contour, 25", Accuracy International AICS 1.5 stock), Brownell's picatinny rings, Vortex Viper HS-T 4-16x44 optics). I truly don't think I could've chosed a better-fitting base. Comes with 6-48 Torx screws, however I usually drill out and install 8-40 screws in my rifles, but since this base has it's own recoil lug that drops down and contacts the front of the cartridge window, I don't think even the heaviest scope will knock it off - I left it at 6-48. The base has a lightening cut down the middle of the "rails", but since this base is made out of tough steel, it's still quite heavy- probably not the best base to choose for a lightweight or mountain rifle. The finish is a matte black oxide finish (or similar) and is extremely tough. I accidentally scraped it while removing release agent from my rifle, didn't even put a ding in it. I have used Badger Ordnance bases in the Army, as well as Leupold Mark 4 bases on other builds, but this Nightforce is my favorite, and will be all I use from now on. Worth every penny.
Produkt č.: 524000016 NIGHTFORCE REMINGTON 700 SHORT ACTION 40 MOA BASE Číslo výrobce: A116847362003085 Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
Jednodílné základny Nightforce jsou obráběny podle specifikace Mil-Std. 1913 pro dokonalé zarovnání, umožňují použití stejného zaměřovače na různých puškách.
Na výběr jsou sklony 20MOA nebo 40MOA (40MOA pouze pro akce Remington), navrženo pro pravé i levé akce bez zásahu do nabíjení nebo vyjímání náboje.
Základna je určena pro model Remington 700 a není kompatibilní s modely WSM.
Atributy
Color:
Black
Material:
Steel
Model:
700
Number of Bases:
1-Piece
Style:
Taktické základny
Udělat:
Remington
Dodací hmotnost: 0,181kgVýška přepravy: 10mmŠířka přepravy: 89mmDélka přepravy: 206mm
UPC
: 847362003085
Detail produktů
Made in USA
New
Produkt č.: 524000006 NIGHTFORCE WINCHESTER 70 LONG ACTION 20 MOA BASE Číslo výrobce: A196847362003894 Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
Produkt č.: 524000007 NIGHTFORCE REMINGTON 700 SHORT ACTION 20 MOA BASE Číslo výrobce: A115847362003078 Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
Produkt č.: 524000008 NIGHTFORCE REMINGTON 700 LONG ACTION 20 MOA BASE Číslo výrobce: A112847362003047 Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
Produkt č.: 524000012 NIGHTFORCE REMINGTON 700 LONG ACTION 20 MOA 2-PIECE BASE Číslo výrobce: A111847362003030 Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
Produkt č.: 749012028 NIGHTFORCE SAVAGE SHORT ACTION ROUND 20 MOA BASE 6-48 SCREWS Číslo výrobce: A168847362003603 Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
Nightforce one-piece bases are machined to exact Mil-Std. 1913 specification rail dimensions, assuring perfect alignment. This design allows the same scope to be used on several different rifles, always optimizing eye relief. Choose from 20MOA or 40MOA tapers (40MOA for Remington actions only). Designed and machined for right- or left- handed actions, Nightforce bases will never interfere with loading or extraction. A168 - Fits Round Receivers
SPECS: Win SA base does not fit WSM Models.
Další...
Jednodílné základny Nightforce jsou obráběny přesně podle rozměrů lišty specifikace Mil-Std. 1913, což zajišťuje dokonalé zarovnání. Tento design umožňuje použití stejného zaměřovače na několika různých puškách a vždy optimalizuje oční reliéf. Můžete si vybrat mezi sklonem 20MOA nebo 40MOA (40MOA pouze pro akce Remington). Navrženo a obráběno pro pravé nebo levé akce, základny Nightforce nikdy nebudou zasahovat do nabíjení nebo vyjímání náboje. A168 - Pasuje na kulaté přijímače
SPECS: Základna Win SA není kompatibilní s modely WSM.
Další...
Hodnocení zákazníků pro položku NIGHTFORCE REMINGTON 700 SHORT ACTION 40 MOA BASE
Počet hodnocení: 8
Od brownells.com: 8
Průměrné hodnocení: 4,5
Does not fit Savage 10 Ashbury Precision(21.11.2017)
First off, the rail is terrific. Steel, perfect level, four screws included (torx head). BUT - be careful if you have a Savage 10 Ashbury Precision. This rail extends an inch or so forward of the front screws and is not high enough to clear the Ashbury handguard. Just wanted to warn any Ashbury owners.
Fit like a glove(20.5.2013)
Expensive and worth every penny.
Broken recoil lug(1.4.2014)
Initially I thought it to be of high quality with a good fit. I tightened the mounting screws well with blue Locktite (did not use torque wrench) and all seemed well however after about 200 rounds 300 Win Mag I noticed erratic groups much worse than initially. I then noticed the recoil lug was cracked and then it fell off when I removed it. I noticed only the second from the front mounting screw to be slightly loose. Luckily they were intact (not sheared off) except for the front screw slightly bent backward (unscrewing noted some rubbing on one side of the screw hole. My load development did go up to loads that had high pressure signs but I stopped immediately after that. The majority of shots were around 78 grains of AA Magpro powder with only flattened primers (ok extraction, no severe cratering). I also used a Lead Sled with about 50lbs of lead so that should have reduced the recoil impulse on the recoil lug. I think the rail should not have failed. The recoil lug is very thin maybe 2mm max. Maybe ok in 308 but not strong enough for the belted Magnums. I was able to zero my Nightforce Competition Scope at 100yds with the 40MOA about 3-4 MOA of down elevation left. So okay at short range if don't need to change windage much
Great value(16.11.2010)
Purchased this from Brownells a while back. I needed more elevation for my Leupold mk4 MR. I am very pleased with this product. It is built quite heavy and works great with the Leupold MK4 rings. As I build more rifles I will use these bases again.
A+ if rifle tapped for right screw(6.3.2010)
This base is designed to never move once mounted. Just make sure your rifle isn't tapped for 8X40 screws like a lot of magnums are. The reason I say this is because you'll be redrilling the mount out and finding larger screws to fit like I am. If Nightforce would tell you the screw size, I never would have ordered this mount for my 300RUM custom made rifle.
Screws(5.1.2012)
Previous review is correct, People often buy NightForce to mount on heavy recoiling long range rifles. (like my Remington in .338 Lapua) These rifles will often have 8 X 40 mount screws but this base is machined for a lighter screw. You will have to re-drill/machine this base to use it on a heavy recoiling rifle with 8 X 40 mounting holes
Best base on the market(25.7.2012)
Anyone that complains that these bases have to be modified to fit a Remington 700 in a magnum has not done their research. Nightforce does offer a 700 base with 8-40 screws. It is called the HS/700 base. A simple call to NF or reading passed the header in the listing would make it clear. I use these bases exclusively on my 6-48 Remington 700 rifles. They have never failed me whether or not I have bedded them. They are bullet proof and absolutely machined to the tightest tolerances. Many of my rifles that I have checked base screw hole alignment have required next to zero windage adjustment with Nightforce scopes, rings, and bases. Thank you Brownells for carrying such high quality components for us.
Simply the best(25.2.2014)
Chose this base for a custom build (Remington 700 short action in .308, Shilen short-chambered Remington stainless barrel, heavy #7 contour, 25", Accuracy International AICS 1.5 stock), Brownell's picatinny rings, Vortex Viper HS-T 4-16x44 optics). I truly don't think I could've chosed a better-fitting base. Comes with 6-48 Torx screws, however I usually drill out and install 8-40 screws in my rifles, but since this base has it's own recoil lug that drops down and contacts the front of the cartridge window, I don't think even the heaviest scope will knock it off - I left it at 6-48. The base has a lightening cut down the middle of the "rails", but since this base is made out of tough steel, it's still quite heavy- probably not the best base to choose for a lightweight or mountain rifle. The finish is a matte black oxide finish (or similar) and is extremely tough. I accidentally scraped it while removing release agent from my rifle, didn't even put a ding in it. I have used Badger Ordnance bases in the Army, as well as Leupold Mark 4 bases on other builds, but this Nightforce is my favorite, and will be all I use from now on. Worth every penny.