Designed for AmeriGlo by well-known M&P customizer David Bowie for a sleek, ultra-low-profile fit on the Smith & Wesson M&P pistol. The rear sight notch is wider and deeper than the factory notch to help you get the front sight centered ASAP. Rounded corners prevent snagging that can impair the draw from concealment.
SPECS: Machined steel, matte black finish. Tritium Front - .435" (11.1mm) long, .140" (3.6mm) wide, .230" (5.8mm) high. Target Front - .400" (10.2mm) long, .140" wide, .230" high. Tritium & Target Rear (All) - .875" (22.2mm) long, .720" (18.3mm) wide rear face, .235" (6mm) overall height above slide, .164" x .115" notch. Tritium sets available with green front/green rear sight (G/G) or green front/yellow rear (G/Y).*Fits all models except Pro Series and "L" versions.
Další...
Nízkoprofilová bojová mířidla
Navrženo pro AmeriGlo známým upravovatelem M&P Davidem Bowiem pro elegantní, ultra-nízkoprofilové nasazení na pistoli Smith & Wesson M&P. Zářez zadního mířidla je širší a hlubší než tovární zářez, což vám pomůže rychleji zaměřit přední mířidlo. Zaoblené rohy zabraňují zachycení, které může narušit rychlé vytáhnutí zpříkrytu.
SPECIFIKACE: Ocelové obrábění, matný černý povrch. Tritiový přední mířidlo - .435" (11.1mm) dlouhé, .140" (3.6mm) široké, .230" (5.8mm) vysoké. Cílové přední mířidlo - .400" (10.2mm) dlouhé, .140" široké, .230" vysoké. Tritiové & cílové zadní mířidlo (Všechny) - .875" (22.2mm) dlouhé, .720" (18.3mm) široké zadní čelo, .235" (6mm) celková výška nad závěrem, .164" x .115" výřez. Sady tritiových mířidel dostupné s zeleným předním/zadním mířidlem (G/G) nebo zeleným předním/žlutým zadním (G/Y).*Vhodné pro všechny modely kromě Pro Series a verzí "L".
Další...
Hodnocení zákazníků pro položku AMERIGLO S&W M&P GREEN/GREEN SIGHT SET
Počet hodnocení: 3
Od brownells.com: 3
Průměrné hodnocení: 4,7
Great M&P9 Night Sights(30.1.2012)
Installed these on my M&P9 full-size. The sights are well made and I was able to get them sighted in perfectly. Nice and bright. Used a sight pusher to install them and it was simple to do.
ALL THAT I WANTED(26.8.2012)
ADDED TO MY S&W M&P 9MM NIGHT STAND WEAPON. TOOK 20 MINUTES AT MY KITCHEN COUNTER, NO VISE OR CLAMPS; USED LIGHT HAMMER, 5/16 BRASS PUNCH AND REAR SIGHT TOOL ($4.00) THIS IS NEEDED TO KEEP SPRING FROM POPPING. OILED EXISTING SIGHTS LOOSENED REAR SET SCREW AND TAPPED OUT SIGHT INSERTING SIGHT TOOL HALFWAY. SAME WITH FRONT, REVERSE PROCEEDURE WITH NEW SIGHTS AND ENJOY
Very Nice Night Sights(6.12.2012)
I picked up a NIB M&P Shield 9mm in a trade recently and decided it needed some night sights since it will be one of my carry guns. After looking at all of the options, I decided on these due to the price point and the styling of the rear sight.
They arrived today and installation was easy enough. Neither the rear nor the front sight needed any fitting. The rear slid in by hand, which is fine since it has the set screw to hold it in place anyway. I felt that the front sight was a little too easy to tap in, so I removed it and added a little loctite under it to make sure it doesn't move under recoil. It probably didn't need it, but I wanted to be sure.
The rear sight didn't really hang over the edge of the slide, but due to the narrower slide on the Shield, the "contour" didn't really match up with the slide. It would in no way affect function, but I took a small file and reshaped the profile of the rear sight (in the area of the dovetail, not the sighting portion) to make it match the slide better. A bluing pen touched up the filed area just fine.
For reference, the front sight is actually finished black much like the factory sights and slide, but the rear sight is more gray, and the bluing pen matched very well. Someone would have to inspect closely to even be able to tell that I did anything to the rear sight.
I have not tested for POI yet, but comparing with the height of the factory sights, this set should do just fine.
The sights are VERY visible in both daylight, low light, and pitch black conditions.
Produkt č.: 100004565 AMERIGLO S&W M&P GREEN/GREEN SIGHT SET Číslo výrobce: SW-801644409017476 Navrženo pro AmeriGlo známým upravovatelem M&P Davidem Bowiem pro elegantní, ultra-nízkoprofilové nasazení na pistoli Smith & Wesson M&P. Zářez zadního mířidla je širší a hlubší než tovární zářez, což vám pomůže rychleji zaměřit přední mířidlo. Zaoblené rohy zabraňují zachycení, které může narušit rychlé vytáhnutí zpříkrytu.
3399CZK23 399,00 Kč
*
Dodací lhůta je přibližně 14-21 dní. 2 Počet ks. skladem USA
Vlastnosti:Make: Smith & WessonModel: M&PSight Color: Green/GreenStyle: Nízkoprofilový, Zaměřovač s nočným videním, 3-Dot, Tritium
Navrženo pro pistoli Smith & Wesson M&P známým upravovatelem Davidem Bowiem, nabízí nízkoprofilový design a rychlejší zaměření díky širšímu a hlubšímu zářezu zadního mířidla.
Vyrobeno z oceli s matným černým povrchem, s tritiovými předními a zadními mířidly dostupnými v zelené/zelené (G/G) nebo zelené/žluté (G/Y) kombinaci.
Vhodné pro všechny modely M&P kromě Pro Series a verzí "L"; zaoblené rohy zabraňují zachycení při rychlém vytahování z přikrýtu.
Designed for AmeriGlo by well-known M&P customizer David Bowie for a sleek, ultra-low-profile fit on the Smith & Wesson M&P pistol. The rear sight notch is wider and deeper than the factory notch to help you get the front sight centered ASAP. Rounded corners prevent snagging that can impair the draw from concealment.
SPECS: Machined steel, matte black finish. Tritium Front - .435" (11.1mm) long, .140" (3.6mm) wide, .230" (5.8mm) high. Target Front - .400" (10.2mm) long, .140" wide, .230" high. Tritium & Target Rear (All) - .875" (22.2mm) long, .720" (18.3mm) wide rear face, .235" (6mm) overall height above slide, .164" x .115" notch. Tritium sets available with green front/green rear sight (G/G) or green front/yellow rear (G/Y).*Fits all models except Pro Series and "L" versions.
Další...
Nízkoprofilová bojová mířidla
Navrženo pro AmeriGlo známým upravovatelem M&P Davidem Bowiem pro elegantní, ultra-nízkoprofilové nasazení na pistoli Smith & Wesson M&P. Zářez zadního mířidla je širší a hlubší než tovární zářez, což vám pomůže rychleji zaměřit přední mířidlo. Zaoblené rohy zabraňují zachycení, které může narušit rychlé vytáhnutí zpříkrytu.
SPECIFIKACE: Ocelové obrábění, matný černý povrch. Tritiový přední mířidlo - .435" (11.1mm) dlouhé, .140" (3.6mm) široké, .230" (5.8mm) vysoké. Cílové přední mířidlo - .400" (10.2mm) dlouhé, .140" široké, .230" vysoké. Tritiové & cílové zadní mířidlo (Všechny) - .875" (22.2mm) dlouhé, .720" (18.3mm) široké zadní čelo, .235" (6mm) celková výška nad závěrem, .164" x .115" výřez. Sady tritiových mířidel dostupné s zeleným předním/zadním mířidlem (G/G) nebo zeleným předním/žlutým zadním (G/Y).*Vhodné pro všechny modely kromě Pro Series a verzí "L".
Další...
Hodnocení zákazníků pro položku AMERIGLO S&W M&P GREEN/GREEN SIGHT SET
Počet hodnocení: 3
Od brownells.com: 3
Průměrné hodnocení: 4,7
Great M&P9 Night Sights(30.1.2012)
Installed these on my M&P9 full-size. The sights are well made and I was able to get them sighted in perfectly. Nice and bright. Used a sight pusher to install them and it was simple to do.
ALL THAT I WANTED(26.8.2012)
ADDED TO MY S&W M&P 9MM NIGHT STAND WEAPON. TOOK 20 MINUTES AT MY KITCHEN COUNTER, NO VISE OR CLAMPS; USED LIGHT HAMMER, 5/16 BRASS PUNCH AND REAR SIGHT TOOL ($4.00) THIS IS NEEDED TO KEEP SPRING FROM POPPING. OILED EXISTING SIGHTS LOOSENED REAR SET SCREW AND TAPPED OUT SIGHT INSERTING SIGHT TOOL HALFWAY. SAME WITH FRONT, REVERSE PROCEEDURE WITH NEW SIGHTS AND ENJOY
Very Nice Night Sights(6.12.2012)
I picked up a NIB M&P Shield 9mm in a trade recently and decided it needed some night sights since it will be one of my carry guns. After looking at all of the options, I decided on these due to the price point and the styling of the rear sight.
They arrived today and installation was easy enough. Neither the rear nor the front sight needed any fitting. The rear slid in by hand, which is fine since it has the set screw to hold it in place anyway. I felt that the front sight was a little too easy to tap in, so I removed it and added a little loctite under it to make sure it doesn't move under recoil. It probably didn't need it, but I wanted to be sure.
The rear sight didn't really hang over the edge of the slide, but due to the narrower slide on the Shield, the "contour" didn't really match up with the slide. It would in no way affect function, but I took a small file and reshaped the profile of the rear sight (in the area of the dovetail, not the sighting portion) to make it match the slide better. A bluing pen touched up the filed area just fine.
For reference, the front sight is actually finished black much like the factory sights and slide, but the rear sight is more gray, and the bluing pen matched very well. Someone would have to inspect closely to even be able to tell that I did anything to the rear sight.
I have not tested for POI yet, but comparing with the height of the factory sights, this set should do just fine.
The sights are VERY visible in both daylight, low light, and pitch black conditions.