If you have and older Ruger® MKI, MKII™ MK4 that's not drilled and tapped you can install this WEIG-A-TINNY® Scopemount without making any permanent alterations to your favorite pistol. Remove the rear sight, insert the threaded dovetail filler and install the mount with the screws provided. Accepts all Weaver style rings and accessories and most Picatinny rings and accessories. 5-1/4" long, silver or Black, matte anodized finish, weighs 2.5 ounces.
Další...
Pokud máte starší Ruger® MKI, MKII™ nebo MK4, který není vyvrtaný a závitovaný, můžete na vaší oblíbené pistoli nainstalovat tuto montáž WEIG-A-TINNY® bez nutnosti jakýchkoliv trvalých úprav. Odstraňte zadní mířidla, vložte závitovou výplň drážky a montáž připevněte pomocí dodaných šroubů. Je kompatibilní se všemi kroužky a příslušenstvím ve stylu Weaver a většinou kroužků a příslušenstvím Picatinny. Montáž má délku 5-1/4 palce, je dostupná ve stříbrné nebo černé matné anodizované úpravě a váží 2,5 unce.
Další...
Hodnocení zákazníků pro položku WEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, BLACK
Počet hodnocení: 5
Od brownells.com: 5
Průměrné hodnocení: 4,6
Gunsmith's Dream(4.11.2009)
The answer to mounting optics to Ruger MK I & MK II Pistols that are not drilled & taped at the factory (non adjustable sights). Just knock out the old sight install the provided dovetailed insert in it's place and fasten on the new base. Doesn't get any more simple than this and the base looks "like it belongs there". No modification to the receiver required.
Good Moiunt(19.12.2009)
I like everything about this mount except it is very tall. Raises the scope center point high above the bore center. This is not such a problem at long range but makes short range shooting more complicated (hold over changes drastically at short ranges.) Mid range trajectory goes higher above sight line than if sight were closer to bore center line. I think they could make this mount thinner. Overall well made, easy to install and solid well engineered. I would buy this again. Slight filing on the steel dovetail mounting block was required. A few light passes is all it took on mine. Tapped it into polace with brass punch.
Easy to Install - Solid Mount(14.2.2011)
I installed this mount on my Ruger 22/45 Target Model, and it went on with no issues. The mount is well finished and machined, and goes on without issue. Tap out existing rear sight with a no-mar removal tool or punch, insert the dovetail base, then attached with the provided screws. I mounted a Burris Fastfire II to it with no issues - works nicely and looks great. Main comment is that it would have been nice if an allen wrench (microscopic size) for the set screws for the base were included in the kit, but I managed to find one to fit them. I would recommend this mount for small red dot sights and very small handgun scopes, due to lack of front tie down screw (but no gunsmithing mods are needed with this rail!). Good product.
Great Service and Great Mount(31.5.2012)
Received the mount in 2 days! It fits exactly as stated. Just a slight tap from a small hammer and it went into the dovetail on my Ruger Mark I. You'll need a couple of Allen wrenches but we all have them anyway. I also used Locktite. Great product to mount a red dot scope on the pistol.
The way to go(22.4.2016)
As advertised, if you have a Ruger Mark I or Mark II and don't want to spend a lot of money having it drilled and tapped for a red dot or scope this is the way to go. Very good directions, simple to install and looks very good. I installed it on a Mark II, put a red dot on it, sighted it in and shot 100 rounds (at customer's request) with no movement of the rail. I call that "very good".
Produkt č.: 957000035 WEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, BLACK Číslo výrobce: RM2SMB Pokud máte starší Ruger® MKI, MKII™ nebo MK4, který není vyvrtaný a závitovaný, můžete na vaší oblíbené pistoli nainstalovat tuto montáž WEIG-A-TINNY® bez nutnosti jakýchkoliv trvalých úprav. Odstraňte zadní mířidla, vložte závitovou výplň drážky a montáž připevněte pomocí dodaných šroubů. Je kompatibilní se všemi kroužky a příslušenstvím ve stylu Weaver a většinou kroužků a příslušenstvím Picatinny. Montáž má délku 5-1/4 palce, je dostupná ve stříbrné nebo černé matné anodizované úpravě a váží 2,5 unce.
2199CZK42 199,00 Kč
*
Dodací lhůta je přibližně 14-21 dní. 4 Počet ks. skladem USA
Vlastnosti:Barevný: BlackMake: RugerMaterial: AluminumModel: Mark IINumber of Bases: 1-PieceStyle: Weaver-styl základny
Montáž WEIG-A-TINNY® umožňuje instalaci na Ruger® MKI, MKII™ nebo MK4 bez nutnosti trvalých úprav.
Kompatibilní se všemi kroužky a příslušenstvím ve stylu Weaver a většinou Picatinny.
Dostupná v černé matné anodizované úpravě, délka 5-1/4 palce a váží 2,5 unce.
Atributy
Color:
Black
Material:
Aluminum
Model:
Mark II
Number of Bases:
1-Piece
Style:
Weaver-styl základny
Udělat:
Ruger
Dodací hmotnost: 0,068kgVýška přepravy: 10mmŠířka přepravy: 86mmDélka přepravy: 170mm
Detail produktů
Made in USA
Produkt č.: 957201100 WEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, SILVER Číslo výrobce: RM2SM Pokud máte starší Ruger® MKI, MKII™ nebo MK4, který není vyvrtaný a závitovaný, můžete na vaší oblíbené pistoli nainstalovat tuto montáž WEIG-A-TINNY® bez nutnosti jakýchkoliv trvalých úprav. Odstraňte zadní mířidla, vložte závitovou výplň drážky a montáž připevněte pomocí dodaných šroubů. Je kompatibilní se všemi kroužky a příslušenstvím ve stylu Weaver a většinou kroužků a příslušenstvím Picatinny. Montáž má délku 5-1/4 palce, je dostupná ve stříbrné nebo černé matné anodizované úpravě a váží 2,5 unce.
2199CZK12 199,00 Kč
*
Dodací lhůta je přibližně 14-21 dní. 1 Počet ks. skladem USA
Vlastnosti:Barevný: SilverMake: RugerMaterial: AluminumModel: Mark IINumber of Bases: 1-PieceStyle: Weaver-styl základny
If you have and older Ruger® MKI, MKII™ MK4 that's not drilled and tapped you can install this WEIG-A-TINNY® Scopemount without making any permanent alterations to your favorite pistol. Remove the rear sight, insert the threaded dovetail filler and install the mount with the screws provided. Accepts all Weaver style rings and accessories and most Picatinny rings and accessories. 5-1/4" long, silver or Black, matte anodized finish, weighs 2.5 ounces.
Další...
Pokud máte starší Ruger® MKI, MKII™ nebo MK4, který není vyvrtaný a závitovaný, můžete na vaší oblíbené pistoli nainstalovat tuto montáž WEIG-A-TINNY® bez nutnosti jakýchkoliv trvalých úprav. Odstraňte zadní mířidla, vložte závitovou výplň drážky a montáž připevněte pomocí dodaných šroubů. Je kompatibilní se všemi kroužky a příslušenstvím ve stylu Weaver a většinou kroužků a příslušenstvím Picatinny. Montáž má délku 5-1/4 palce, je dostupná ve stříbrné nebo černé matné anodizované úpravě a váží 2,5 unce.
Další...
Hodnocení zákazníků pro položku WEIGAND COMBAT RUGER MK I, MK II, 22/451-PIECE BASE, BLACK
Počet hodnocení: 5
Od brownells.com: 5
Průměrné hodnocení: 4,6
Gunsmith's Dream(4.11.2009)
The answer to mounting optics to Ruger MK I & MK II Pistols that are not drilled & taped at the factory (non adjustable sights). Just knock out the old sight install the provided dovetailed insert in it's place and fasten on the new base. Doesn't get any more simple than this and the base looks "like it belongs there". No modification to the receiver required.
Good Moiunt(19.12.2009)
I like everything about this mount except it is very tall. Raises the scope center point high above the bore center. This is not such a problem at long range but makes short range shooting more complicated (hold over changes drastically at short ranges.) Mid range trajectory goes higher above sight line than if sight were closer to bore center line. I think they could make this mount thinner. Overall well made, easy to install and solid well engineered. I would buy this again. Slight filing on the steel dovetail mounting block was required. A few light passes is all it took on mine. Tapped it into polace with brass punch.
Easy to Install - Solid Mount(14.2.2011)
I installed this mount on my Ruger 22/45 Target Model, and it went on with no issues. The mount is well finished and machined, and goes on without issue. Tap out existing rear sight with a no-mar removal tool or punch, insert the dovetail base, then attached with the provided screws. I mounted a Burris Fastfire II to it with no issues - works nicely and looks great. Main comment is that it would have been nice if an allen wrench (microscopic size) for the set screws for the base were included in the kit, but I managed to find one to fit them. I would recommend this mount for small red dot sights and very small handgun scopes, due to lack of front tie down screw (but no gunsmithing mods are needed with this rail!). Good product.
Great Service and Great Mount(31.5.2012)
Received the mount in 2 days! It fits exactly as stated. Just a slight tap from a small hammer and it went into the dovetail on my Ruger Mark I. You'll need a couple of Allen wrenches but we all have them anyway. I also used Locktite. Great product to mount a red dot scope on the pistol.
The way to go(22.4.2016)
As advertised, if you have a Ruger Mark I or Mark II and don't want to spend a lot of money having it drilled and tapped for a red dot or scope this is the way to go. Very good directions, simple to install and looks very good. I installed it on a Mark II, put a red dot on it, sighted it in and shot 100 rounds (at customer's request) with no movement of the rail. I call that "very good".