Hammer has three heads; brass, nylon and steel. Two heads mount to the blued steel hammer head, to the blued steel hammer head, the third attached to the base of the knurled brass handle. Brass drift punch stores in handle. Great for knocking out pins.
Další...
Kladivo má tři hlavice; mosaznou, nylonovou a ocelovou. Dvě hlavice se montují na modřenou ocelovou hlavici kladiva, třetí je připevněna k základně rukojeti s vroubkovaným mosazným povrchem. Mosazný vyháněcí punc se ukládá do rukojeti. Skvělé pro vyhazování kolíků.
Další...
Hodnocení zákazníků pro položku LYMAN BRASS TAPPER AND DRIFT PUNCH
Počet hodnocení: 1
Od brownells.com: 1
Průměrné hodnocení: 4
It has limits. (6.10.2017)
It's a neat little hammer and punch kit. You can keep the brass head and steel head in the hammer for a bit more power, or remove them both and use the plastic head only for delicate tasks. For lite use, such as driving pins, this kit is perfect. The punch fits inside the hollow handle. Think: "lite use" with this kit.
I used it to remove and install dovetail sights (both front and rear) on several older and newer .22LR rifles. A couple of my front sights were really tough to remove, but I stayed at it. The job really deformed the head of the brass punch. It almost looks like a mushroomed bullet that I recovered from an Elk. I originally bought it to keep in my travel gear, with the intent of using it to drift sights at the range. It might work for that purpose, provided the sights are not really tight. But, as I stated above, it's really not up to that task. I've ordered a stronger (?) drift punch, and hope it holds up to sight installation. I'm going to try to file this deformed punch flat. Good luck.
Produkt č.: 749002611 LYMAN BRASS TAPPER AND DRIFT PUNCH Číslo výrobce: 7031290011516812902 Kladivo má tři hlavice; mosaznou, nylonovou a ocelovou. Dvě hlavice se montují na modřenou ocelovou hlavici kladiva, třetí je připevněna k základně rukojeti s vroubkovaným mosazným povrchem. Mosazný vyháněcí punc se ukládá do rukojeti. Skvělé pro vyhazování kolíků.
1249CZK01 249,00 Kč
*
Předbjednávka, dodací lhůta je přibližně 4-12 týdny ze skladu z USA.
Hammer has three heads; brass, nylon and steel. Two heads mount to the blued steel hammer head, to the blued steel hammer head, the third attached to the base of the knurled brass handle. Brass drift punch stores in handle. Great for knocking out pins.
Další...
Kladivo má tři hlavice; mosaznou, nylonovou a ocelovou. Dvě hlavice se montují na modřenou ocelovou hlavici kladiva, třetí je připevněna k základně rukojeti s vroubkovaným mosazným povrchem. Mosazný vyháněcí punc se ukládá do rukojeti. Skvělé pro vyhazování kolíků.
Další...
Hodnocení zákazníků pro položku LYMAN BRASS TAPPER AND DRIFT PUNCH
Počet hodnocení: 1
Od brownells.com: 1
Průměrné hodnocení: 4
It has limits. (6.10.2017)
It's a neat little hammer and punch kit. You can keep the brass head and steel head in the hammer for a bit more power, or remove them both and use the plastic head only for delicate tasks. For lite use, such as driving pins, this kit is perfect. The punch fits inside the hollow handle. Think: "lite use" with this kit.
I used it to remove and install dovetail sights (both front and rear) on several older and newer .22LR rifles. A couple of my front sights were really tough to remove, but I stayed at it. The job really deformed the head of the brass punch. It almost looks like a mushroomed bullet that I recovered from an Elk. I originally bought it to keep in my travel gear, with the intent of using it to drift sights at the range. It might work for that purpose, provided the sights are not really tight. But, as I stated above, it's really not up to that task. I've ordered a stronger (?) drift punch, and hope it holds up to sight installation. I'm going to try to file this deformed punch flat. Good luck.