Košík je prázdný.

Košík

Help a kontakt

Doprava zdarma při nákupu nad 5 999,00 Kč

100denní politika vrácení

Novinky

Slevy

Přes 300 000 zákazníků - děkujeme vám!

4,93/5 "Velmi dobré" (1400+ hodnocení)

40 000+ produktů pro lov a střelbu

CASPIAN
1911 SLIDES

168000050

Superb Strength & Precise Tolerances For The Ultimate Combat Pistol

Custom-quality slides from Caspian, ready to be fitted to the frame of your choice. They start as high-quality forgings for extra strength, then are heat-treated to Rc 38-41 before machining for exceptional dimensional stability. Sides are polished, while the rest of the surface is bead-blasted for a non-glare, matte finish. Deep-cut, forward-angled rear cocking serrations prevent slippage when racking, even with a wet hand. Available in 4340 carbon steel (CS) and 416 stainless steel (SS) with .45 ACP, .40 S&W, and 9mm breechfaces. Commander and Officers models in .45 ACP only. Choose a slide without sight cuts (NC), or between two pre-cut dovetail options: a Novak Lo-Mount or Bo-Mar BMCS rear cut, both coupled with a Novak front cut. Recon slide is a Government slide with ball cuts at the front that line up with the light rail on the Caspian Recon frame (available separately). All slides require the use of a 9mm/.38 Super firing pin.

SPECS: 4340 carbon steel, in-the-white, or 416 stainless steel, natural finish. Government model accepts 5" barrel. Commander accepts 4.25" barrel. Officers model accepts 3.5" barrel. All Caspian slides require the use of a 9mm/.38 Super firing pin.

Další...

Vynikající pevnost & přesné tolerance pro ultimátní bojovou pistoli

Závěry od Caspian kvality na zakázku, připravené k osazení na vámi vybraný rám. Začínají jako kovaniny vysoké kvality pro extra pevnost, poté jsou tepelně zpracovány na Rc 38-41 před obráběním pro výjimečnou stabilitu rozměrů. Boky jsou leštěny, zatímco zbytek povrchu je matován tryskáním pro neslunečný, matný finiš. Hluboké, vpřed šikmé zadní zářezy pro natahování zabraňují skluzu při nabíjení, i když jsou ruce mokré. Dostupné v 4340 uhlíkové oceli (CS) a 416 nerezové oceli (SS) s nábojovými plochami pro .45 ACP, .40 S&W a 9mm. Modely Commander a Officers pouze pro .45 ACP. Vyberte si závěr bez výřezů pro mířidla (NC), nebo mezi dvěma předem připravenými možnostmi výřezů pro dovetail: Novak Lo-Mount nebo Bo-Mar BMCS zadní výřez, oba ve spojení s Novak předním výřezem. Závěr Recon je Government závěr s kuličkovými výřezy vpředu, které se shodují s kolejnicí pro svítilnu na rám Caspian Recon (dostupný zvlášť). Všechny závěry vyžadují použití zápalníku pro 9mm/.38 Super.

SPECS: 4340 uhlíková ocel, v surovém stavu, nebo 416 nerezová ocel, přírodní povrch. Government model přijímá 5" hlaveň. Commander přijímá 4.25" hlaveň. Officers model přijímá 3.5" hlaveň. Všechny závěry od Caspian vyžadují použití zápalníku pro 9mm/.38 Super.

Další...

Hodnocení zákazníků pro položku CASPIAN CARBON STEEL, NC SIGHT CUT, 9MM

Počet hodnocení: 6
Od brownells.com: 6
Průměrné hodnocení: 3,8

Very nice slide! (12.8.2012)

Fit perfectly except for a little work to get the barrel bushing to fit. I'm extremely happy with it. It isn't quite a "drop in replacement" but, I had no trouble fitting it to my frame. I highly recommend it as a replacement slide for a Colt Officers model. Especially, since the actual Colt ones are getting harder to find.

Not for all (20.4.2012)

I ordered the slide for my build, a 45 ACP, the slide looks great and is good quality. I was hopeing to be able to switch slides back and forth, between the Gov and commander modle. The slide did not fit at all on the frame, so I took it to my local gunsmith to have it fitted, after about a week he notified me that not only uses a 9 mm fireing pin (which I knew) but also a 9 mm ejector (not mentioned anywhere) and that the 45 ACP ejector would not work at all. So as soon as my gunsmith puts the 45 back into its original configuration, I'll try to figure something else out. My recomendation, if you have a Mil Spec 45 this slide may not be for you.

Exactly what i wanted, Quick, Easy (19.3.2010)

This slide is a stainless commander length, of course. It has the rear slanted classic style serrations. NO front serrations, lowered and flared ejection port, Caspian "C" logo on both sides under the rear sight and CASPIAN engraved in the left ( I think, i don't have it in front of me.) It is well finished, NO burrs, If there are any machine marks, they are not visible or i missed them. Edges were crisp but not sharp. I will end up rounding off all edges though. When i got it, it was in a box from Caspian with the stainless note (says if you aren't careful/fit the slide improperly there is a possibility you can break off the rear left part, the notch behind where the thumb safety locks in. IF YOU BREAK IT, YOUR SLIDE WILL NOT BE REPLACED) and some type of grease paper. [...]The slide would go about half way down my frame, which i think is about perfect. I haven't got to fit it yet but I am confident it will fit right. I have a used factory Colt .45 barrel going in it for now and it locked and unlocked very nicely. Locked SOLID. The factory barrel bushing that went with the Colt barrel fit very tight in the slide, but went in correctly. Very good. the firing pin and spring went in no issue ( small diameter firing pin [.38]) The extractor goes all the way in but fits very tight, i think i will sand a couple thousands off of it just to get it in and out. The one thing i didn't try was to see if the firing pin stop went in without fitting, and I haven't received my sights yet, so i can't say how they fit. I am very pleased. I was not able to find another slide i liked anywhere except Caspian themselves, the issue there is the wait while they build it, not that that is bad. I am very "picky when it comes to guns, cars, women, and parts for all..... I know what i want to build before i start. This slide actually exceeded my expectations. I will order another Caspian the next time i build a 1911.P.S. In this review, further down, it has multiple choices for pros and cons. One listed under cons is fitting required. I think this is good. I want every part to fit my gun as well as possible. Some may want to buy a part and it go straight on, thats fine too. SO, my opinion is that minor fitting is a pro. As

Not so good. (4.10.2014)

Not much about this slide was good, but may have just been my luck at getting a not so good one. The front Novak sight cut was bad and took me 4 hours with a file and a knife edge stone to get it to work. I have tried 4 different barrels and hours of filing and stoning and I still can't get one to lock up right. Might be just my luck, but I may not buy another one, ever.....

New Project (29.10.2011)

I mated this slide to a stainless Essex frame I previously had fit a Remington Rand blued slide on. The Caspian slide completed the all stainless look, and I fit an Ed Brown stainless barrel Colt Commander bobbed hammer and Smith and Alexander Mainspring. The frames blued componets were removed and replaced with all stainless slide lock, safety and mag release. The final product is a great looking, great shooting chunk of shiny 1911!

**Springfield rebuild** (11.12.2016)

Fitted this SS Caspian slide to a Springfield Armory 1911-A1 frame. Rebuilt this 1911 with all new parts from Brownell's. The fit and finish of this slide is beautiful. I would definitely choose Caspian for all my future builds.

<img width="500" src='/userdocs/reviewimages/6c1c11d3-788f-4011-b5c4-bfdf0d081392.jpg' alt=''>

Přečtete si další hodnocení na webu brownells.com

10399 15499 22 CZK

Produkt č.: 168000050
CASPIAN CARBON STEEL, NC SIGHT CUT, 9MM
Číslo výrobce: 168-000-050 Závěry od Caspian kvality na zakázku, připravené k osazení na vámi vybraný rám. Začínají jako kovaniny vysoké kvality pro extra pevnost, poté jsou tepelně zpracovány na Rc 38-41 před obráběním pro výjimečnou stabilitu rozměrů. Boky jsou leštěny, zatímco zbytek povrchu je matován tryskáním pro neslunečný, matný finiš. Hluboké, vpřed šikmé zadní zářezy pro natahování zabraňují skluzu při nabíjení, i když jsou ruce mokré. Dostupné v 4340 uhlíkové oceli (CS) a 416 nerezové oceli (SS) s nábojovými plochami pro .45 ACP, .40 S&W a 9mm. Modely Commander a Officers pouze pro .45 ACP. Vyberte si závěr bez výřezů pro mířidla (NC), nebo mezi dvěma předem připravenými možnostmi výřezů pro dovetail: Novak Lo-Mount nebo Bo-Mar BMCS zadní výřez, oba ve spojení s Novak předním výřezem. Závěr Recon je Government závěr s kuličkovými výřezy vpředu, které se shodují s kolejnicí pro svítilnu na rám Caspian Recon (dostupný zvlášť). Všechny závěry vyžadují použití zápalníku pro 9mm/.38 Super.

10399 CZK 0 10 399,00 Kč *

Předbjednávka, dodací lhůta je přibližně 4-12 týdny ze skladu z USA.

Vlastnosti: Finish: Unfinished Make: 1911 Model: Government Mířidla: No Cuts Náboj: 9 mm Luger Style: Government, Zadní zoubkování

CASPIAN 1911 SLIDES

Hodnocení zákazníků pro položku CASPIAN CARBON STEEL, NC SIGHT CUT, 9MM

Omezení

Top takeaways

Atributy

Detail produktů

Hodnocení zákazníků pro položku CASPIAN CARBON STEEL, NC SIGHT CUT, 9MM

Připojení

Bezpečné platební metody

Obchodní asociace

Vítejte!

CASPIAN
1911 SLIDES